Before Using Setting the Measuring and Memory button configuration In the custom settings mode refer to P40 , the Measuring button and the Memory button can be set as follows.
For Incident measuring The Measuring button and Memory button is set in the standard configuration. Page Setting Measuring Mode 4. Page Incident Measurement Mode Incident Measurement Mode Incident light measuring is the measurement method that employs either the Lumisphere or Lumidisc functions.
Measurements should be with the Lumisphere aimed towards the camera direction from the subject position. Basic Operation Reflected Measurement Mode spot metering This method measures the brightness luminance of the light reflected from the subject.
It is useful for distant objects such as landscapes, when you cannot go to the position of the subject, or for metering subjects that generate light neon signs, etc. Page 22 5. O Exposure Over is displayed,it indicates that the measured exposure is outside the display range, changing the shutter speed to a faster setting with the Jog wheel will allow you to find a combination of proper aperture and shutter speed.
Page Ev Mode 5. Measurement EV mode 1. To activate EV mode, please set Custom setting no. See page 40 2. Page Cinematography Cinematography 1. Turn the Jog wheel to select the Cine Speed for the camera that will be used. Page 26 5. Measurement 4. Page Measuring Electronic Flash Measuring electronic flash This method of measurement can be done in the following modes; with cord, without cord, and Wireless flash radio triggering mode cumulative or non-cumulative. When Measuring flash light, the shutter speed and F stop value value combining ambient light and flash light: total amount of light are displayed.
Page 29 3. The ready to measure mode will continue for approximately 90 seconds. During this time, trigger the flash to make a measurement. Measurement Cord multiple flash cumulative mode These measurements are used when the light generated by the flash is inadequate for proper exposure. The repeated flash pops can be accumulated until the desired aperture is displayed. The cumulative number is infinite. Only one digit is displayed if the cumulative number is ten or more.
Under such conditions, it is recommended that you use the meter in the cordless flash mode, or wireless flash radio triggering mode and keep the Synchro terminal cap in place. Page 32 5. Measurement 2. When the light from the flash is received, the measured value f stop is displayed. Each time this is repeated, the accumulated value for the aperture and the number of cumulative flashes is displayed. The ready to measure mode will be displayed for approximately 90 seconds. It is also possible to modify the ratio by adjusting the flash light when changing the distance between the flash and the subject or when changing the amount of light of the flash.
Page Wireless Flash Radio Triggering 5. Measurement Wireless Flash Radio Triggering With the Radio Transmitter module plugged into the meters radio socket and a Receiver or Transceiver PocketWizard a convenient system that enables one person working alone to measure flash output without the need of a sync cord. Pressing the Measuring button simultaneously triggers the flash and measures the flash output simultaneously.
Page 35 4. In the Quad-Triggering zone setting, after the channel is set to 17 to 32, the assigned buttons below are pressed. Pressing each of the buttons activates or deactivates the Quad- Triggering zone A, b, c or d. When a Quad-Triggering zone is activated, the corresponding Quad-Triggering zone letter appears on the display.
Page 36 5. Page Advanced Functions Memory function This meter can store up to nine measured values in memory for incident light and reflected light simultaneously. This feature can be used in the following modes; Ambient light : shutter speed priority, aperture priority or EV mode. Electronic Flash light : cord, cordless or wireless flash radio triggering mode. Page Averaging Function 6. Advanced Functions Averaging function This function displays the average of up to nine of the values in memory.
Current measured value on the analog scale will blink. Page 39 Turn any secondary light source off. Point the Lumisphere toward the main light source, from the position of the subject and take a measurement. Set meter to spot reading for reflected light. Take the measurement by looking through the finder and aligning so the subject that will be measured is inside the circle.
Page Filter Compensation 6. Advanced Functions Filter compensation Filter compensation 1 It is possible to compensate for filter factor within a range of 5. Highlight and shadow compensation values can also be enter for quick exposure metering. Select setting number 1 and item number 2 in the custom setting mode see page Page Custom Setting Function 6. Advanced Functions Custom setting function The following Custom Settings provide a quick and easy setup of individual meter preferences.
All preferences are stored on a memory chip and can not be deleted, they can only be changed back to default settings. Page 47 To enter the custom setting mode, the meter must first be turned off. In addition, since film and digital cameras have their own unique dynamic range, clipping point expo- sure tolerance and varying ISO sensitivity they need to be profiled. Film exposures should be evalu- ated by scanning the film first and then evaluating the images in a photo application software.
Page Input Test Target Data Input test target data There are two ways to input the result of the test target data into the light meter: 1 Sekonic Data Transfer Software - install application software from the included CD-ROM and connect the com- puter and light meter via USB, and 2 Direct Input - Manually enter the test target data directly into the light meter.
Take the measurement by looking through the sekonic ldr manual and aligning so the subject that will bemeasured is inside the circle. The ready to measure mode will continuefor approximately 90 seconds. Wireless Flash Radio Triggering 5. Select setting number 1 and item number 2 in the custom setting mode see page Measurement Aperture Priority mode1.
Actual LCD screen will not show all icon as above during normaluse. Memory function This meter can store up to nine measured values in memory for incident light and reflected light simultaneously. Setting the Measuring and Memory button configurationIn the custom settings mode refer to P40the Measuringbutton and the Memory button can be set as sekonic ldr manual. Please read the note swkonic avoid incorrect opera- tion.
Sekonic ldr manual Measurement ModeIncident light measuring is the measurement method thatemploys either the Lumisphere or Lumidisc functions. An exposuremeter, a camera, and a flash sekonic ldr manual all be connected at thesame time. Measurements should be with the Lumisphere aimed towards the camera direction from the subject position.
Place the meter parallel to the subject and take ameasurement. Measuring sekonic ldr manual flash This method of measurement can be lrr in the following modes; with cord, without cord, and Wireless flash sekonic ldr manual triggering mode cumulative or non-cumulative. Pressing each of the buttons activates or deactivates the Quad- Triggering zone A, b, c sekonic ldr manual d. The ready to measure mode will be sfkonic for approximately 90 seconds.
Turn the main lighting off. Or point us to the URL where the manual is located.
0コメント